Grundfos MAGNA3 40-60F circulating pump 220 mm
- EAN no.: 5710626493425
- LM no.: 380792061
- Supplier: Grundfos
Must login for adding to cart
Description
Type no: 97924267
Promotion code: 1123030420112
UNSPSC (v. 19.0501): 40151504
HS Code: 84137030
MAGNA3 40-60 F
MAGNA3 – More than a pump With its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.
The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.
The pump is characterised by the following:
controller integrated in the control box
control panel with TFT display on the control box
control box prepared for optional CIM modules
built-in differential-pressure and temperature sensor
cast-iron pump housing (depending on model)
carbon-fiber-reinforced composite rotor can
stainless-steel bearing plate and rotor cladding
aluminium alloy stator housing
air-cooled power electronics
The MAGNA3 is a single-phase pump.
Characteristic features
AUTOADAPT.
FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).
Proportional-pressure control.
Constant-pressure control.
Constant-temperature control.
Constant-curve duty.
Max. or min. curve duty.
Automatic Night Setback.
No external motor protection required.
Insulating shells supplied with single-head pumps for heating systems.
Large temperature range where the liquid temperature and the ambient temperature are independent of each other.
Communication The MAGNA3 enables communication via the following:
wireless Grundfos GO Remote
fieldbus communication via CIM modules
digital inputs
relay outputs
analog input (more than a pump function as heat energy meter)
Motor and electronic controller The MAGNA3 incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than
a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter. A differential-pressure and temperature sensor is incorporated in the pump.
Liquid:
Pumped liquid: Water
Liquid temperature range: -10 .. 110 °C
Selected liquid temperature: 60 °C
Density: 983.2 kg/m³
Technical:
Rated flow: 9.4 m³/h
Rated head: 4.28 m
TF class: 110
Approvals on nameplate: CE,VDE,EAC,CN ROHS,WEEE
Materials:
Pump housing: Cast iron
EN-GJL-250
ASTM A48-250B
Impeller: PES 30%GF
Installation:
Range of ambient temperature: 0 .. 40 °C
Maximum operating pressure: 10 bar
Flange standard: DIN
Pipe connection: DN 40
Pressure stage: PN 6/10
Port-to-port length: 220 mm
Electrical data:
Power input - P1: 12 .. 185 W
Main frequency: 50 / 60 Hz
Rated voltage: 1 x 230 V
Maximum current consumption: 0.11 .. 1.58 A
Enclosure class (IEC 34-5): X4D
Insulation class (IEC 85): F
MAGNA3 – More than a pump With its unrivalled efficiency, all-encompassing range and built-in communication capabilities plus functionalities replacing system components, the MAGNA3 is ideal for engineers and specifiers looking to create high-performance systems for buildings. This pump in the Grundfos Master Class will fit both heating and cooling applications perfectly, making it the obvious choice for almost any building project – old or new.
The MAGNA3 is of the canned-rotor type, i.e. pump and motor form an integral unit without shaft seal and with only two gaskets for sealing. The bearings are lubricated by the pumped liquid. The innovative clamp with only one screw enables easy repositioning of the pump head. The MAGNA3 is a pump with no maintenance requirements and with extremely low Life Cycle Cost.
The pump is characterised by the following:
controller integrated in the control box
control panel with TFT display on the control box
control box prepared for optional CIM modules
built-in differential-pressure and temperature sensor
cast-iron pump housing (depending on model)
carbon-fiber-reinforced composite rotor can
stainless-steel bearing plate and rotor cladding
aluminium alloy stator housing
air-cooled power electronics
The MAGNA3 is a single-phase pump.
Characteristic features
AUTOADAPT.
FLOWADAPT and FLOWLIMIT (more than a pump function as it reduces the need for pump throttling valves).
Proportional-pressure control.
Constant-pressure control.
Constant-temperature control.
Constant-curve duty.
Max. or min. curve duty.
Automatic Night Setback.
No external motor protection required.
Insulating shells supplied with single-head pumps for heating systems.
Large temperature range where the liquid temperature and the ambient temperature are independent of each other.
Communication The MAGNA3 enables communication via the following:
wireless Grundfos GO Remote
fieldbus communication via CIM modules
digital inputs
relay outputs
analog input (more than a pump function as heat energy meter)
Motor and electronic controller The MAGNA3 incorporates a 4-pole synchronous, permanent-magnet motor (PM motor). This motor type is characterised by higher efficiency than
a conventional asynchronous squirrel-cage motor. The pump speed is controlled by an integrated frequency converter. A differential-pressure and temperature sensor is incorporated in the pump.
Liquid:
Pumped liquid: Water
Liquid temperature range: -10 .. 110 °C
Selected liquid temperature: 60 °C
Density: 983.2 kg/m³
Technical:
Rated flow: 9.4 m³/h
Rated head: 4.28 m
TF class: 110
Approvals on nameplate: CE,VDE,EAC,CN ROHS,WEEE
Materials:
Pump housing: Cast iron
EN-GJL-250
ASTM A48-250B
Impeller: PES 30%GF
Installation:
Range of ambient temperature: 0 .. 40 °C
Maximum operating pressure: 10 bar
Flange standard: DIN
Pipe connection: DN 40
Pressure stage: PN 6/10
Port-to-port length: 220 mm
Electrical data:
Power input - P1: 12 .. 185 W
Main frequency: 50 / 60 Hz
Rated voltage: 1 x 230 V
Maximum current consumption: 0.11 .. 1.58 A
Enclosure class (IEC 34-5): X4D
Insulation class (IEC 85): F