Parker F37-324-50X5.0TFBCF flange halvpart komplet hydraulik stål kromatiseret

Den Par Flange F37 Flanged connector system is utilising the orbital rør forming technology til tubing assemblies fra 16 til 273 mm (1/2" til 10" Flanges) outside diameter. It is intended til rør wall thickness up til 9 mm og tryk ratings up til 420 bar. til those forbindelser without the possibility til assemble a pre-flared rør or where manufacturing is limited, Parker giver the F37 Retaining Ring system. This system utilizes a Retaining Ring til Flange retention along med a highly-engineered tætning carrier til leak free performance. It is tilgængelig as a højtryk version fra 1 1/2" til 10" og as a newly developed SAE 1000 (50-70 bar) version. The Par Flange F37 system corresponds til hole patterns according til ISO 6162-1; SAE J518; bore pattern 3000 (code 61), ISO 6162-2; bore pattern 6000 (code 62) og also ISO 6164 bore pattern. It is type approved by DNV, ABS og other major classification companies. • Marine • Offshore • Tungt industrimateriel • Værktøjsmaskiner • Materialehåndtering • Mobile industrier • Energiproduktion • Pressebygning • Miljø • Hydrogen Innovative tætning Solutions The F37 tætning was developed especially til use med SAE Flanges. These special seals guarantee high stability af form. Compared til standard O-Rings, their mechanical properties forhindre gap extrusion, even when the Flanges ”breathe” under tryk. The special profile af the F37 tætning is ideally adapted til higher pressures or unsuitable surface finish af the Flanges. As an alternative, connectors can be equipped med bonded tætning rings. Complete sortiment til virtually all diameters The F37 system complements the EO-2 soft tætning technology til small rør diameters; it also complements the proven Par Flange programme til the SAE product sortiment. It tilbyder the complete sortiment af connectors, Flange-til- Flange, L-og T-Block connectors, Flange-til-port, han og hun gevind Flanges, Flange bends, reducer Flanges, ball ventiler, bulkhead Flanges og manifolds on request. The F37-Programme – a savings programme F37 is the way til reduce manufacturing times enormously. By comparing welded forbindelser med Parker Flange connector systemer, significant opportunities til cost savings become immediately obvious. The typical process af rør welding consist af the following steps: 1. Cutting og deburring rør 2. rør preparation til the connecting process 3. Welding og/or assembling 4. Inspection (X-ray) af welded connectors 5. Flushing the connected rør 6. Applying korrosion protection i comparison med this, weld-free rør forming save time og costs. Expensive cleaning og X-raying af the rør connector become immediately things af the past. The manufacturing time til a rør connector quickly reducerer by more than half i comparison med conventional welding. Parker Flange connector systemer accommodate high krav, especially those fra the offshore industry, shipbuilding, heavy maskiner konstruktion og press manufacture, as well as fra mining, recycling plants og mobile maskiner; overall i power piping systemer. Personnel og miljø-friendly By comparing the individual operations til a welded line med Parker Flanges connected lines, significant cost savings opportunities become immediately obvious. No vapours putting health at risk are released, i contrast til conventional welding processes. Consequently, usage is possible i locations med high krav such as, til example, offshore olie platforms. i addition til this flaring machine design errors i the preparation af Flanges are virtually unknown. Stress korrosion cracking generated during welding operations is history og the life af the finished tubing system is increased. Cold formed Par Flange technologies save power og energy compared til welding og require neither degreasers nor anti-korrosion agents. When galvanized rør are used, post-galvanization can be omitted because the zinc-coating is not impaired by flaring. Parker Flange connector components are delivered i state af the art Cr(VI)-free surfaces. egenskaber, advantages og fordele No welding • reduceret preparation time per joint • No costly inspection af welds (X-ray) No post-weld cleaning • No acid cleaning costs • No waste cleaning costs • No sikkerhed risk • Environmentally friendly No welding stress korrosion possible • Maximum piping lifetime • reduceret maintenance costs No „hot work“ permit required • Operation can take place i areas med fire risk without interruption af production • reduceret downtime costs • Higher level af sikkerhed Work shop prefabrication • High quality joints med better accuracy due til workshop conditions • Minimized need til on-site work • Shorter installation time • Shorter maintenance/downtime • Shorter total project time Cleanliness • Minimized need til repair og replacement af hydraulisk system components such as pumps, cylinders,… • reduceret overall flushing time og costs nem dismantling og reassembling • Quicker, easier og more flexible installation • reduceret downtime costs til maintenance og repair • It is tilgængelig as a højtryk version fra 1 1/2" til 10" og as a newly developed SAE 1000 (50-70 bar) version. • Tubing assemblies fra 16 til 273 mm (1/2" til 10" flanges) outside diameter. • High-tryk flange forbindelser med tryk ratings up til 420 bar. • forbindelser where a pre-flared rør cannot be samlet or where manufacturing is limited.